🛍️ Store link: Philips EasyKey 7300-5HB
📘 Please refer to the full lock's User Manual 🔗
✅ The manual includes answers to common questions and step-by-step help for setup and troubleshooting.
Important Information
Security and Caution
Read and understand all instructions before using the Philips EasyKey. Damage from not following instructions is not covered by the warranty.
Use only manufacturer-specified accessories and components.
Only use the alkaline batteries that came with the product or an equivalent type.
Do not forcibly disassemble the lock, as this may trigger an alarm or damage the product.
Avoid scraping the fingerprint sensor with sharp objects to prevent permanent damage.
Do not expose the product to water or corrosive substances.
Do not hang objects on the handle.
Clean the product with a soft cloth.
Do not remove the batteries during setup or operation.
A professional technician should install the door lock.
Immediately change the default master PIN code after installation.
Replace all batteries as soon as a low battery alarm sounds. Ensure the poles are matched correctly (+/-).
Do not place batteries near a fire.
Do not connect the two battery poles with metal.
Any component replacement should be done by Philips, an authorized service center, or a professional technician.
Using parts or accessories not recommended by Philips may void your warranty.
Used products and batteries should be disposed of according to local regulations and should not be mixed with ordinary domestic waste.
Installation
The installation steps in the manual are for right-open doors. For left-open doors, adjustments are required.
Package Contents
The package includes the following items for reference:
Outside escutcheon (with silicone pad)
Inside escutcheon (with silicone pad)
Drilling template
Mortise
Mounting plate
User manual
Quick start guide
Warranty card
Certificate of Quality
Smart door card (x2)
Mechanical key (x2)
Batteries
Installation kit
Scouring pad
Striker
Pre-installation Instructions
1. Check the door opening direction:
The lock can be installed on doors with four opening directions: left-out pull, right-in push, right-out pull, and left-in push.
2. Change the handle direction:
Unscrew and remove the direction adjustment stand.
Rotate the handle 180 degrees.
Adjust the cable, put the stand back, and tighten the screws.
3. Change the latch bolt direction:
Push the inverting tailpiece to the top.
Press the latch bolt down, rotate it 180 degrees, and pull it out.
Push the tailpiece to the bottom.
Change the direction of the directional screw. It must be installed on the inside of the door.
Note: The default toolkit works for doors with a thickness of 38-60mm. If your door is outside this range, you must contact Philips.
Installation Steps
Use the drilling template to drill the necessary holes and install the mortise.
Tighten the four fixed screws when inserting the mortise.
Install the connecting screw tube, and place the square shaft and compressed spring into the lever hole. The spring must be towards the lever.
Pass the connection wire through the hole in the mortise. Align the cylinder key tailpiece and square shaft with the two rotary holes on the mortise and insert them.
Tighten the mounting plate with three anchor screws against the inside of the door.
Place the compressed spring and then the square shaft into the inside escutcheon. Insert the connection and mortise wires into the sockets on the inside escutcheon.
Align the square shaft with the mortise holes and insert them so the inside escutcheon is close to the inside of the door.
Tighten the two anchor screws.
Install the batteries, the battery cover, and the inside lower cover.
Test the inside and outside levers and the mechanical key to check that all components are working correctly.
Getting to Know Your EasyKey
The lock has several components on the outside and inside escutcheons.
Outside Escutcheon
Keypad
Card reader
Mute button
Low battery indicator
Outside forced lock button
Fingerprint sensor
Lever
Door status indicator
Emergency power interface
Mechanical keyhole
Inside Escutcheon
Battery cover
Lever
Safe handle switch
Reset button
Close button
Setting Up Your EasyKey
The default master PIN code is 12345678.
How to Enter Master Mode
Press the pound key [#].
After the voice prompt, enter the master PIN code and press [#] to confirm.
User Settings
Modify Master PIN Code
Enter master mode (see above).
Press [1].
Enter the new master PIN code and press [#].
Re-enter the new master PIN code and press [#] to confirm.
Register a User PIN Code
Enter master mode.
Press [2], then press [1]. The system will automatically number the user.
Enter a 6 to 12-digit PIN code and press [#].
Re-enter the same PIN code and press [#] to confirm.
Register a One-Time User PIN Code
Enter master mode.
Press [2], then press [2].
Enter a 6 to 12-digit one-time PIN code and press [#].
Re-enter the PIN code and press [#] to confirm.
Register a Fingerprint
Enter master mode.
Press [2], then press [3]. The system will automatically number the fingerprint.
Place your finger on the sensor.
Follow the voice prompts to place your finger on the sensor multiple times until you hear "Succeeded".
Register a Card
Enter master mode.
Press [2], then press [4]. The system will automatically number the card.
Hold the card against the card reader until you hear a beep.
Delete a User
Delete a Single User PIN Code
Enter master mode.
Press [3], then press [1].
Press [1] again to delete a single PIN code.
Enter the 2-digit user number of the PIN code you want to delete and press [#].
Delete All User PIN Codes
Enter master mode.
Press [3], then press [1].
Press [2].
Delete a One-Time User PIN Code
Enter master mode.
Press [3], then press [2].
Delete a Single Fingerprint
Enter master mode.
Press [3], then press [3].
Press [1].
Enter the 2-digit user number of the fingerprint you want to delete and press [#].
Delete All Fingerprints
Enter master mode.
Press [3], then press [3].
Press [2].
Delete a Single Card
Enter master mode.
Press [3], then press [4].
Press [1].
Delete All Cards
Enter master mode.
Press [3], then press [4].
Press [2].
System Settings
Language Settings: The default language is English.
Enter master mode.
Press [4], then press [1].
Press [1] for Chinese, [2] for English, [3] for Spanish, [4] for Russian, or [5] for Arabic.
Volume Settings: The default is "higher volume".
Enter master mode.
Press [4], then press [2].
Press [1] for higher volume, [2] for lower volume, or [3] for mute mode.
Switch to Dual Verification Mode:
Enter master mode.
Press [4], then press [3].
Press [1] for single verification or [2] for dual verification.
Other Functions
Anti-fake Code Query:
Enter master mode.
Press [6], then press [1]. The serial number will be broadcast.
Alternatively, you can input 400# as a shortcut.
System Query:
Enter master mode.
Press [6], then press [2]. The software version will be broadcast.
Local Query: The shortcut is 114#.
Bluetooth Settings:
To enable, press [7], then press [1].
To disable, press [7], then press [3].
Shortcuts: 403# to open, 404# to turn off.
How to Use Your EasyKey
Unlocking from Outside
With PIN code:
Touch the keypad to wake the system.
Enter your registered PIN code and press [#].
After the "Door opened" voice prompt, press the handle down.
With Fingerprint:
Place your registered finger on the sensor.
After the "Door opened" voice prompt, press the handle down.
With Card:
Place your registered card on the card reader.
After the "Door opened" voice prompt, press the handle down.
Unlocking from Inside
The door can be opened by directly pressing down on the handle.
Ensure the safe handle switch is toggled to the green scale to disable the safe handle function.
Locking
Auto/Manual Mode:
The lock is in auto mode by default.
In auto mode, the deadbolt automatically pops up and locks the door after it is closed.
In manual mode, the deadbolt does not pop up automatically. You must press the [Close] button to lock the door.
To switch modes, long-press the [6] key in the unlocked state.
Deadlock from Inside
To enable: Long-press the [CLOSE] button until it flashes red and you hear "Inside deadlock enabled".
When enabled, all functions on the outside escutcheon are locked. The keypad will display "15937(X)" if you try to wake it up.
To unlock, you must use the master PIN code or the mechanical key.
Mechanical Key Opening
This is for emergencies only (e.g., low battery, forgotten PIN code, or system failure).
Cut the box and take out the key shell.
Push the cover aside to reveal the key.
Insert the key into the keyhole, keeping the key and key shell vertical to each other.
Rotate the key shell toward the handle by 90° until it's close to the door.
Rotate the key shell downwards by 180° to be parallel with the ground.
Rotate the key shell horizontally toward the handle to unlock the door.
Other Functions
Safe Handle Function:
When enabled, the handle is locked from the inside, and the door cannot be unlocked from the inside.
To enable, toggle the switch on the inside escutcheon to the red scale.
To disable, toggle the switch to the green scale.
One-Button Mute Function:
When the system is awake, long-press the [Mute] button for 2 seconds to enter mute mode. The button will glow green.
To unmute, long-press the [Mute] button for 2 seconds. The button will glow white.
Restore to Factory Settings:
Double-click the [RES] button with a sharp object until you hear "Restored to factory settings".
All user information will be emptied.
Outside Forced Lock Function:
After the door is locked, long-press the functional button for 2 seconds to enter this mode.
When enabled, unlocking from the inside will trigger an alarm.
Troubleshooting
Alarm Types
Low Battery Alarm: When the battery voltage is too low, the light will flash red, and you will hear "Low battery. Please replace all batteries" during unlocking.
Anti-dismantle Alarm:
Trigger 1: The door is pried open, and the sensor bolt pops up.
Trigger 2: The outside escutcheon is pried open.
The alarm will be continuous and repeate,d and can be turned off by a successful verification or by closing the door.
Abnormal Latch Bolt Alarm: The latch bolt cannot lock or unlock properly. The alarm is continuous and will automatically turn off.
Outside Forced Unlock Mode: Inside unlocking alarm. The alarm will be continuous and repeated, and can be turned off by a successful verification method of any type.
Emergency Power Supply
If the batteries are dead, you can power up the lock by plugging a 5V power bank into the micro USB port.
If the system crashes, a 5V power bank can be used to reboot it.
How to Replace Batteries
The lock uses four AA alkaline batteries.
There are two power stations, allowing for a total of eight batteries to extend battery life.
To access the batteries, push the button at the top of the inside escutcheon to remove the battery cover.