Skip to main content

DDL210X-13H Installation Guide

Installation Video Guide

Installation steps:

Required Tools

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Tools

Prepare the door and check dimensions

  1. Measure to confirm that the hole in the door is 1-1/2″ or 2-1/8″ (38mm or 54mm). Measure to confirm that the hole in the door edge is 1″ (25mm).

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig1

  2. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60mm or 70mm).
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig2

  3. Measure to confirm that the door is 1-3/8″ to 2″ (35mm to 50mm) thick.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig3


    ​

  4. Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig4


    ​
    ​

    warning 2

    Attention
    Make sure the door frame is aligned with the door and there are no obstructions in the door frame.

Determine backset and adjust the latch
​

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig5


Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
​
​YES - No adjustment is required. Proceed to next step.

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig6


​NO -Slotted hole is NOT centered.
​

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig7


Rotate and pull the latch as shown to extend latch.

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig8


​

Install the latch bolt

PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig9

  1. Use a screwdriver to confirm that the deadbolt locks and unlocks smoothly.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig10


    ​

  2. Install the strike on the door frame.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig11


    ​

    warning 2

    Attention: Make sure the hole in dthe oor frame is drilled a minimum of 1″(25mm) deep


    ​Install exterior assembly


  3. ​Attention: Before installation, make sure the latch is fully retracted (in the unlocked position).
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig12


    ​

  4. With the latch bolt fully retracted (in the unlocked position), route the cable from the exterior keypad assembly below the latch.
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig13

  5. Measure the diameter of the hole in the door.
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig14

  6. Move the buttons on both sides of the interior assembly upwards to remove the mounting plate from the interior base.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig15


    ​

  7. Secure the mounting plate with the Mounting Plate Screws. Do not overtighten screws.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig16


    ​
    ​


    ​

    Install the interior assembly

  8. Push the battery cover up in the direction as illustrated.
    ​

    Attention: Do not load batteries before finishing the lock installation.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig17

  9. Insert the cable connector of the exterior assembly to the socket on the interior assembly. Push the connector in firmly until it is completely attached.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig18

  10. Keep the thumb turn in the vertical position and install the Interior Assembly.
    ​
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig19


    ​

  11. Attach the Interior Assembly to the Mounting Plate and fasten using the Interior Assembly Screws.
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig20

  12. Install the AA batteries.
    ​

    PHILIPS DDL210X-13H Home Access Matte Black Electronic Deadbolt Biometric Lock - Fig21

  13. Press and hold the Reset Button for at least 5 seconds until you hear a beep. This activates the lock-handling process and must be completed before setting up the lock.

warning 2

Attention: Ensure the cable is not pinched, or the lock will not function properly.

Did this answer your question?